Overview

The Unit Test Plan (UTP) will follow the same section breakdown as the Requirements in the Scope & Requirement Document.

The following types of tests shall be included where it makes sense.

In-Range UT - these are the test cases which cover normal operations.
Out-of-Range UT - these are the test cases which cover out of range scenarios:
1. border cases
2. race conditions
3. unexpected events
  1. EX: Tearing down an active Network Interface
Error UT
1. Error parameters
2. Error Conditions
  1. network goes down unexpectedly
  2. Wire gets disconnected, etc

Performance Testing cases will be a separate section in this document.

Unit Test Plan

Configuration tests should be done through the DLC direct interface, as well as the YAML interface.

Local Network Configuration

In-Range UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-020	cfg-005, cfg-010, cfg-015,cfg-045, cfg-055, cfg-060, cfg-065	UT-0005	Configure 3 NIDs on the same TCP network. Show the NIDs
		UT-0010	Configure 3 NIDs on the same IB network Show the NIDs
		UT-0015	Configure 3 NIDs on the same TCP/IB Network Show the NIDs Delete 1 NID from the TCP/IB Network Show the NIDs
		UT-0020	Configure 2 NIDs on tcp0/o2ib0 Configure 2 NIDs on tcp1/o2ib1 Show the NIDs Delete 1st NID from tcp0 Delete 2nd NID from tcp0 Show NIDs No more tcp 0 should exist o2ib0 should be unaffected
cfg-025	cfg-005, cfg-010, cfg-015,cfg-045, cfg-055, cfg-060, cfg-065	UT-0025	Configure the system to have 4 CPTs options libcfs cpu_npartitions=4 cpu_pattern="0[0] 1[1] 2[2] 3[3]" Configure 2 NIDs on tcp0 NID 1 should be on CPTs 0, 3 NID 2 should be on CPTs 1, 2 Show NIDs proper CPT association should be displayed
cfg-035	cfg-040, cfg-045, cfg-055, cfg-060, cfg-065	UT-0030	Configure the system to have 4 CPTs options libcfs cpu_npartitions=4 cpu_pattern="0[0] 1[1] 2[2] 3[3]" Configure 3 NIDs on tcp0 NID 1 should be on CPTs 0, 3 NID 2 should be on CPTs 1, 2 NID 3 should be on all CPTs Show NIDs proper CPT association should be displayed NID 3 should exist on all CPTs
		UT-0035	Configure 1st NID on tcp0 using the legacy ip2nets parameter from DLC Show NIDs
		UT-0040	Configure 1st NID on tcp/o2ib in the following ip2nets form: tcp(<eth intf>)[<cpt>] <pattern> Show NIDs to ensure that the interface has been added to the correct CPTs
		UT-0045	Configure 1st NID on tcp/o2ib in the following ip2nets form: tcp(<eth intf>, <eth intf>, ...)[<cpt>] <pattern> Show NIDs to ensure that the interface has been added to the correct CPTs
		UT-0050	Configure 1st NID on tcp/o2ib in the following ip2nets form: tcp(<eth intf>[<ctp>], <eth intf>[<ctp>], ...) <pattern> Show NIDs to ensure that the interface has been added to the correct CPTs
cfg-060	cfg-065	UT-0055	Go through the following lnetctl commands and excercise their parameters: net set num_range

Out-of-Range UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-020	cfg-005, cfg-010, cfg-015	UT-0060	Configure 32 NIDs on the same TCP/IB Network Show the NIDs
		UT-0065	Configure 32 NIDs on the same TCP/IB Network Show the NIDs. Delete 32 NIDs on the same TCP/IB Network
		UT-0070	Configure NID A, B and C on tcp0/o2ib0 Network Configure NID A and B on tcp1/o2ib1 Network Show the NIDs Configuration should succeed. NIs can exist on different networks
cfg-060	cfg-065	UT-0075	Go through the following lnetctl commands and excercise their parameters, by providing out of range values: net set num_range
		UT-0080	Don't configure any LNet modprobe. Load LNet where there exists only one commissioned IB interface with IPoIB configured a TCP network should be created with that IB interface Configure an o2ib network with the same IB interface Now you should have two interfaces with exactly the same IB

Error UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
		UT-0085	Configure 128 NIDs on the same TCP/IB Network Only the maximum NIDs will be configured
		UT-0090	Configure a non-existent NID on tcp0 Configuration should fail with INVALID PARAMETER
		UT-0095	Configure the system to have 4 CPTs options libcfs cpu_npartitions=4 cpu_pattern="0[0] 1[1] 2[2] 3[3]" Configure 3 NIDs on tcp0 NID 1 should be on CPTs 0, 4 NID 2 should be on CPTs 1, 2 NID 3 should be on all CPTs Show NIDs NID 1 should fail since no CPT 4
		UT-0100	Go through the following lnetctl commands and excercise their parameters, by providing error values: net set num_range
		UT-0105	Delete a non-existent network
		UT-0110	Delete a non existent NID on tcp/o2ib

Remote Peer Configuration

Expected Behavior

A peer can be added by specifying a list of NIDs
- The first NID shall be used as the primary NID. The rest of the NIDs will be added under the primary NID
A peer can be added by explicitly specifying the key NID, and then by adding a set of other NIDs, all done through one API call
If a key NID already exists, but it's not an MR NI, then adding that Key NID from DLC shall convert that NI to an MR NI
If a key NID already exists, and it is an MR NI, then re-adding the Key NID shall have no effect
if a Key NID already exists as part of another peer, then adding that NID as part of another peer shall fail
if a NID is being added to a peer NI and that NID is a non-MR, then that NID is moved under the peer and is made to be MR capable
if a NID is being added to a peer and that NID is an MR NID and part of another peer, then the operation shall fail
if a NID is being added to a peer and it is already part of that Peer then the operation is a no-op.

In-Range UT

Primary Requirement ID	Unit Test ID	Unit Test Description
cfg-070	UT-0115	add a new peer with only 1 NID
cfg-070	UT-0120	add a new peer with only 1 NID add more nids to that peer
cfg-070	UT-0125	add a new peer with mulitple NIDs
cfg-070	UT-0130	add a new peer with only 1 NID Delete that NID
cfg-070	UT-0131	add a new peer with multiple NIDs delete the primary NI of the peer The entire peer should be deleted.
cfg-070	UT-0135	add a new peer with multiple NIDs Delete each NID one at a time until the peer is removed
cfg-070	UT-0140	add a new peer with multiple NIDs Delete all NIDs but primary NID only. Re-add multiple NIDs one at a time.
cfg-070	UT-0145	add a new peer with multiple NIDs Delete all NIDs but primaray NID. Re-add multiple NIDs in one shot.
cfg-075	UT-0150	add a new peer with multiple NIDs on different networks

Out-of-Range UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
		UT-0155	add a new peer with 32 NIDs
		UT-0160	delete a peer and all its 32 NIDs
		UT-0165	load lnet lnetctl lnet configure add 2 or more peers on a non-local network delete peer 1 delete peer 2
		UT-0170	load lnet lnetctl lnet configure add 2 or more peers on a non-local network lnetctl lnet unconfigure lustre_rmmod
		UT-0171	load lnet lnetctl lnet configure add 2 or more peers on tcp1 (non-local) check that refcount = 2 (1 for hashlist & 1 for remote list) check credits are not set add tcp1 network Check refcount 1 (remote list refcount removed) check credits are set
		UT-0172	load lnet lnetctl lnet configure add 2 or more peers on tcp1 (primary peer ni) add 2 or more peers on tcp2 add tcp 1 and tcp 2 networks remove the tcp1 network check that the entire peer is removed
		UT-0173	same steps as above remove a tcp2 network check that all peers on that network are removed.
		UT-0175	startup lnet startup traffic add a peer ni on a non-local network add a local network for that peer Send traffic over that peer_ni
		UT-0176	startup lnet add tcp1 network add peers on tcp1 network check they are multi-rail run taffic delete the peers peers should be recreated because of traffic and they should be non-mr

Error UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-070		UT-0180	add more than 32 NIDs
cfg-070		UT-0185	add a peer with multiple NIDs delete a non-existent peer NID from the peer identified by key-NID
cfg-080	snd-065	UT-0190	add peer 1 with NIDs A, B and C add peer 2 with NIDs D, C and E Adding NID C should fail

Policy Configuration

In-Range UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-090		UT-0195	Set the NUMA range to 0 The NI closest to the message memory NUMA will be picked.
cfg-090		UT-0200	Increase the NUMA range step by step Note that more NIs are picked when sending
cfg-090	snd-025	UT-0205	Set the NUMA range to a large value start traffic NIs are picked in round robin

Error UT

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-090		UT-0210	Set the NUMA range to < 0 This should be rejected

General Configuration

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
cfg-170		UT-0215	Configure multiple NIs Configure multipe Peers with multiple NIDs set NUMA range value Dump the YAML configuration use the YAML configuration file to delete all configuration use the YAML configuration file to reconfigure the node.

Functional Requirements

Interface Selection and Message Sending Requirements

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
snd-005		UT-0220	Configure 3 NIs with equadistant NUMA distance Send three or more messages Dump statistics on each NI to verify that each NI was used to send messages
snd-010	snd-015	UT-0225	Configure 3 NIs closer to different NUMA nodes dump the NI statistics Verify that each NI has the correct device CPT
snd-020		UT-0230	Configure 3 NIs with different NUMA distances Send messages Confirm through statistics that messages are being sent over the nearest NI (NUMA wise)
snd-020		UT-0235	Configure 2 NIs with different NUMA distances Send messages Confirm through statistics that messages are being sent over the nearest NI (NUMA wise) add another NI which is close NUMA wise than the current nearest confirm through statistics that messages are not being sent over the newly added NI
snd-030		UT-0240	Configure 3 NIs, one EDR, one FDR and one QDR set the NUMA range to a large value so all NIs are considered through RR start traffic monitor statistics on each NI. Confirm that EDR is preferred until it becomes saturated, then FDR is selected then QDR
snd-030		UT-0245	Configure 3 NIs set the NUMA range to a large value so all NIs are considered through RR start traffic monitor statistics on each NIs to confirm all are being used. Remove one of the NIs Confirm that that NI is no longer used for new messages Confirm that the other 2 NIs are being used. No messages should be dropped.
snd-035		UT-0250	Configure 3 NIs Configure a peer with 3 NIDs Send messages to the peer Confirm through statistics that peer NIDs are being used based on their available credits.
snd-040		UT-0255	Configure 3 NIs which are not equadistant all on the same network configure a peer with 3 NIDs all on the same network start traffic Confirm closest NUMA NI is being used Confirm peer NIDs are being used set NUMA range to a large value Confirm all NIs are being used Confirm no change in traffic pattern to the peers
snd-045	snd-070	UT-0260	Configure NIs A, B and C Configure the peer with the same NIDs Send 1 message which requires a response from NI A Confirm that responses are being sent to the same NI
snd-050		UT-0265	Configure NIs A, B and C Configure the peer with the same NIDs Send 1 message which requires a response from NI A bring down NI A confirm that response is sent to one of the other configured NIDs
snd-050		UT-0270	Configure an MR system Start traffic monitor traffic is being sent to all configured peers bring down one of the peer NIDs monitory traffic is no longer sent to that peer NID no messages should be dropped
snd-050	snd-060, snd-075	UT-0275	Configure an MR system Start traffic monitor traffic is being sent to all configured peers bring down one of the peer NIDs monitory traffic is no longer sent to that peer NID bring up the peer NID again monitor traffic is being sent to it again
snd-055	snd-060, snd-075	UT-0280	Configure an MR system Start traffic monitor traffic is being sent to all configured peers bring down one of the peer NIDs monitory traffic is no longer sent to that peer NID bring down all peer NIDs message should fail.
snd-055	snd-060, snd-075, snd-085	UT-0285	Configure an MR system Start traffic monitor traffic is being sent to all configured peers over all NIs bring down the local NIs one by one note traffic is migrated to the NIs still up, until no NIs are left then messages are dropped
snd-055	snd-060, snd-075, snd-085	UT-0290	Configure an MR system Start traffic monitor traffic is being sent to all configured peers over all NIs bring down the local NIs one by one note traffic is migrated to the NIs still up, until no NIs are left then messages are dropped bring up the NIs again and confirm that NIs are being reused.
snd-055	snd-060, snd-075	UT-0295	Configure two networks tcp and o2ib Configure nodes to have multiple interfaces on each of the networks start traffic over the o2ib network o2ib should be used bring down the o2ib network traffic should migrage to the tcp network. no traffic should be dropped.
snd-080		UT-0300	Configure an MR system bring down an NI confirm that the show info shows the NI as down
snd-080		UT-0305	TODO: how do we test device failure?
		UT-0310	Configure an MR system Configure peers via DLC Run traffic Delete one of the peer_nis we're sending to via DLC Traffic going over that peer_ni should continue but no more traffic should use that NI
		UT-0315	Configure an MR system Configure peers via DLC Run traffic Delete one of the peer_nis we're sending to via DLC Bring that peer_ni back Note traffic stops and starts on that peer with no traffic loss Repeat the deletion and reconfiguration of the peer_ni
		UT-0320	Configure an MR system Configure peers via DLC Run traffic Delete the entire peer The peer should be recreated on the next message, but it won't be MR capable.

Dynamic NID Discovery

Debugging Requirements

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
dbg-005	dbg-010, dbg-015, dbg-020, dbg-025, dbg-030, dbg-035, dbg-080	UT-0325	dump per NI statistics transmitted received dropped timeouts state
dbg-040	dbg-080, dbg-095	UT-0330	configure multiple NIs run traffic dump stats on all NIs
dbg-040	dbg-080	UT-0335	configure multiple NIs run traffic dump stats on all NIs Filter on specific NID
dbg-045	dbg-080	UT-0340	dump LNet level statistics
dbg-050	dbg-080, dbg-100	UT-0345	configure multiple peers start traffic dump per peer statistics
dbg-110		UT-0350	configure multiple NIs toggle their state from ACTIVE to DOWN confirm that state change is being printed to console.
dbg-115		UT-0355	configure an MR system start traffic bring down an NI confirm that messages indicating that another NI/peer is being used is printed.
dbg-120		UT-0360	Configure an MR system run traffic stop traffic dump NI statistics dump peer statistics dump LNet level statistics zero out stats dump all statistics above to confirm they've been zeroed out.

Network interface Health

Backwards Compatibility Requirements

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
bck-025		UT-0365	Configure an MR client Configure an MR OSS Configure a non-MR MDS/MGS create an FS Run IO tests Make sure that MR clients/OSS integrates seamlessly in the system.

Performance Requirements

Primary Requirement ID

Secondary Requirement ID

Unit Test ID

Unit Test Description

UT-0370

Testing reconnects. In Large clusters it is possible that servers might need to handle a burst of client connects.

The performance of such scenarios needs to be quantified.

Misc Error Scenarios

Primary Requirement ID	Secondary Requirement ID	Unit Test ID	Unit Test Description
			mount an File System delete all networks from the MDS
			mount an File System delete all networks from the MDS
			mount an File System delete all networks from the MDS
			mount an FS reboot the MDS mount the MDS again
			mount an FS reboot the OSS mount the OSS again
			mount an FS reboot the Client mount the Client again
			mount an FS with no modprobe.conf configured the tcp network with a default tcp interface should be configured add the same interface again via DLC This operation should be a no-op